We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Take Off BOA Snowboard Boots: A Step-by-Step Guide

Learn how to take off BOA snowboard boots in a few steps, including how to release the dial, loosen the laces and avoid damaging the system.

Updated November 2026

To take off BOA snowboard boots, you release the tension by turning the dial counterclockwise or pulling the dial outward, then slide your foot out without yanking the laces. Once the cable is loose, the boot opens fully and you can step out in seconds. The steps below cover a standard single or double BOA setup and how to avoid the common mistakes that wear out the cable over time.

Why the BOA System Releases Differently Than Laces

A BOA boot uses a thin steel or synthetic cable routed through guides down the boot shell, all tightened by a dial on the outside of the cubby. Turning the dial pulls the cable tight; releasing it lets the cable slide back out. Because the tension is spread evenly along the cable, you don’t need to untie anything. The trick is to release tension at the dial first, not by pulling on the boot or the cable itself.

Shopping for one? See our guide: 6 Best Snowboard Boots with BOA for Every Rider (2026). For another angle, check out Boot Dryer Red Wing: How to Dry Red Wing Boots Safely in 5 Steps.

Step-by-Step: Taking Off Your Boots

  1. Unbuckle your bindings first. Trying to pull a boot out of a strapped-in binding puts stress on the cable guides.
  2. Find the dial. On most boots it sits on the outside of the upper, near the ankle or calf.
  3. Turn the dial counterclockwise. Many models also have a release button or a pull-to-release tab. Press or pull it to let the cable run free.
  4. Wait a second for the cable to slacken. You should feel the upper loosen around your shin and instep.
  5. Loosen the top cable if your boot has two dials. On double BOA boots, release the upper dial and the lower dial separately so tension doesn’t build up on one side.
  6. Slide your foot out. Push the heel forward and pull your foot up and out, keeping your ankle straight rather than twisting.

What to Do If the Dial Won’t Turn

A dial that feels stuck is usually packed with snow, ice or grit, or the cable has been pulled too hard. Knock the boot against a hard surface to dislodge debris, then try again. Don’t force the dial past its natural stop. If the cable has jumped out of a guide, a bootfitter or the manufacturer’s service center can usually re-seat it. Consult a professional if you see a frayed cable or a damaged dial.

Tools and Setup That Make Removal Easier

Situation What Helps
Cold weather, stiff cable Warm the boot briefly in your hands or near a heater before turning the dial
Wet or icy dial Wipe it dry and clear snow out of the dial housing
Double BOA boots Release both dials before pulling your foot out
Tight fit at the heel Loosen the lower dial first, then the upper

Common Mistakes to Avoid

  • Pulling the boot off by the cable or the dial instead of releasing tension first.
  • Leaving the binding straps locked, which forces you to twist your foot out.
  • Cranking the dial past its stop, which can strip the internal gears over time.
  • Ignoring snow buildup in the dial, which makes it harder to turn each time.
  • Skipping the upper dial on double BOA boots and forcing the heel out.

A small boot dryer helps clear moisture from the dial housing and liner after a day on the hill, which keeps the mechanism turning smoothly. View on Amazon

A soft-bristled brush is handy for clearing snow and grit from the dial and cable guides before you release tension. View on Amazon

FAQ

Do I need to unbuckle my bindings before taking off BOA boots?

Yes. Unbuckling the bindings first prevents strain on the boot and makes it much easier to slide your foot out without twisting.

Can I remove the BOA cable entirely?

Most people shouldn’t. Removing the cable is a repair task, and a bootfitter or manufacturer service center should handle it to avoid damage.

Why does my BOA dial feel harder to turn in the cold?

Cold stiffens the cable and any moisture in the dial can freeze. Warming the boot slightly and clearing debris usually restores smooth operation.

Conclusion

Taking off BOA boots comes down to releasing the dial first, then loosening the cable and sliding your foot out. Unbuckle your bindings, use the release on double-dial models, and keep the dial clean. Follow those habits and your boots will last longer and come off easily every time.

Emily Parker

About Emily Parker

Emily Parker is part of our editorial team and reviews and edits our snowboarding guides, checking product details against manufacturer specifications and owner feedback.

About the author

Emily Parker
Emily Parker

Emily Parker writes reviews and buying guides for Snowboard Everest.