Mounting a Snowboard on the Wall: A Step-by-Step Guide for Riders
Learn how to mount a snowboard on the wall safely, with the right hardware, stud spacing, and height tips so your board stays put.
Updated November 2026
Mounting a snowboard on the wall is a simple job that keeps your board off the floor, out of the way, and easy to grab before the first lift. You will need the right wall hardware, a level reference line, and solid anchor points in the wall. Done correctly, the board stays secure whether it hangs flat or on its edge.
Choose the Right Wall and Hardware
Pick a wall that can carry the load. A snowboard plus boots, bindings, and a bag adds up quickly, so mount into wall studs or use heavy-duty masonry anchors rated for the weight. Avoid drywall anchors alone, since they tend to pull out under the sway of a heavy board.
Shopping for one? See our guide: Freestyle All Mountain Snowboard: 3 Best Picks for Park and Trail (2026).
Most riders use one of two setups. A horizontal rack with two or more cradles holds the board flat, which takes less wall space. A vertical rack or single hook lets you hang the board on its edge, which is common for narrower boards that you want to display.
Mount the Rack Step by Step
- Measure the board’s length and decide where it will sit. Leave clearance for the bindings so they do not catch on furniture or door frames.
- Hold the rack against the wall and use a level to mark the top and bottom screw holes. Keep the line straight, since a tilted rack will slowly slide the board off.
- Locate the studs with a stud finder and mark their centers. If you are hanging on studs, align at least one screw in each mounting plate with a stud.
- Drill pilot holes slightly smaller than the screw diameter. For masonry, drill into the wall using the bit size the anchor manufacturer specifies.
- Install the anchors if needed, then fasten the rack. Tighten firmly, but do not overdrive the screws, which can strip the holes.
- Test the rack by pulling down on it with moderate force before placing the board. Then set the board in the cradles and check that it sits without rocking.
Set the Height and Spacing
Hang the board so the bottom of the rack is at a comfortable height for lifting and setting down, usually around chest level or a little lower for adults. If you have children in the house, keep the board higher so it stays out of reach. Also keep the bindings clear of the floor and walkways.
Check the spacing between cradles against your board’s contact points. Many boards have a wider waist and a different tail shape, so position the cradles where the board rests on stable, flat sections rather than on the edges or inserts.
Mounting on Concrete or Brick
Masonry walls need hardware made for that material. Use the anchor type the rack maker recommends, drill to the specified depth, and clean out the dust before inserting the anchor. This keeps the grip strong over time.
Common Mistakes
- Relying on drywall anchors alone for a board and gear.
- Skipping the level, which leaves the board tilted and prone to sliding.
- Mounting too high to reach safely when lifting the board.
- Placing the rack where the bindings bump into doors or traffic paths.
- Forgetting to recheck the screws after a few weeks, since loosened hardware can shift the board.
Recommended Gear
- Stud finder: A reliable stud finder helps you locate solid framing before drilling, which matters most for a loaded rack. View on Amazon
- Torpedo level: A short level makes it easier to keep the rack straight on tight spaces. View on Amazon
- Heavy-duty wall anchors: Masonry anchors suit brick or concrete walls where studs are not available. View on Amazon
For help choosing the right boots and bindings to pair with your board, see What Are BOA Snowboard Boots? How the Lacing System Works and Twin or Directional Snowboard for Beginner (2026): Which Should You Choose?.
FAQ
Can I mount a snowboard on drywall without studs?
It is not recommended. Drywall anchors can pull out under the weight and movement of a board and gear. Use wall studs or masonry anchors rated for the load.
How high should a snowboard rack be?
A height around chest level or slightly lower works well for most adults, since it makes lifting and setting the board down easier. Raise it if children are in the home.
Should I hang the board flat or on its edge?
Flat mounting uses a horizontal rack and takes up less wall space. Edge mounting suits a vertical rack and displays the board more prominently, but confirm the hardware is rated for it.
Conclusion
Mounting a snowboard on the wall comes down to solid anchors, a level line, and a sensible height. Take a few extra minutes to find studs and test the rack before loading it. A well-mounted board stays secure and ready for your next day on the hill.
Related reading
- Womens Thirtytwo BOA Snowboard Boots: How to Pick the Right Pair (2026)
- Womens Snowboard Boots BOA Lacing: How to Get a Locked-In Fit
- Womens BOA Snowboard Boots Size 8: How to Get the Right Fit
- Womens BOA Snowboard Boots Sale: How to Pick a Pair That Fits (2026)
Ready to choose one?
