We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Snowboard Mount for Wall: A Step-by-Step Guide to Storing Your Board (2026)

Learn how to choose and install a snowboard mount for wall, from finding studs to spacing brackets, so your board stores safely off the floor.

Updated November 2026

A snowboard mount for wall gives you a safe, tidy place to store your board between sessions. This guide walks you through choosing the right mount, locating solid anchor points, and installing it so the board stays put. You will finish with a secure setup that keeps the edges protected and the base off damp concrete.

Choose the Right Type of Wall Mount

Most snowboard mounts for wall fall into two families: horizontal racks that hold the board flat, and vertical hooks or clips that hold it on its edge. Horizontal racks take up more wall space but are easier to load and unload. Vertical mounts save room and suit narrow garage or closet walls. Check the mount’s stated maximum board width and weight before buying, and make sure it accepts the sidecut and tip shape of your board. Wide all-mountain or freeride boards sometimes overhang a narrow bracket, so measure first.

Shopping for one? See our guide: Freestyle All Mountain Snowboard: 3 Best Picks for Park and Trail (2026).

Find Solid Anchor Points

A board weighs more than most people expect once you add bindings, and the mount has to hold that load every time you pull it out. Drywall alone will not do it. Use a stud finder to locate wood studs, and aim to anchor at least one screw into each stud you use. If your studs are not where you need them, install a backing board across two or more studs first.

  1. Mark the stud centers with a pencil and check them with a second pass of the finder.
  2. Hold the mount level against the wall and mark the screw holes.
  3. Drill pilot holes slightly smaller than the screw shank, so the threads bite without splitting the wood.
  4. Drive lag screws or structural screws into the studs, not just into drywall anchors.
  5. Tighten until the bracket is snug, then test it with a firm downward pull before loading the board.

Space and Position the Mount Correctly

Position matters as much as the hardware. Keep the board off the floor so the base does not sit in moisture or rest against a cold concrete slab. A height of about 12 to 18 inches from the floor works well for horizontal racks, and at a comfortable reach for vertical hooks. Leave clearance for bindings so they do not jam into the wall or the next board. If you store two boards, space the mounts far enough apart that the tips and tails do not touch.

Protect the Base and Edges

Keep the base facing away from the wall and avoid letting edges rest on bare metal brackets for long periods. A thin foam or rubber pad on each contact point reduces scraping and helps prevent edge damage. Store the board clean and dry, and wipe off any wax or snow before hanging it.

Checklist Before You Hang Your Board

  • Stud finder and pencil
  • Level
  • Drill with bits sized for your screws
  • Lag or structural screws rated for the load
  • Padding for contact points
  • Tape measure to confirm board width and clearance

Common Mistakes to Avoid

  • Relying on drywall anchors alone for a loaded board.
  • Mounting the rack too high to lift the board safely.
  • Ignoring binding clearance and hanging the board where it binds against the wall.
  • Storing the board on a cold, damp floor or against a wall that sweats.
  • Skipping the pull test after installation.
  • Stud finder: A reliable stud finder makes it far easier to locate the framing behind drywall, which is the single most important step for a secure mount. View on Amazon
  • Structural lag screws: Heavy-duty screws grip wood studs better than standard wood screws and hold a loaded board securely. View on Amazon
  • Rubber or foam padding: Adhesive pads protect the base and edges from metal contact and reduce scratches. View on Amazon

FAQ

Can I mount a snowboard on drywall without studs?

It is not recommended. Drywall anchors can fail under the weight of a board and bindings, especially when the board is pulled out or bumped. Mount into studs or install a solid backing board first.

How high should a snowboard mount for wall be?

For horizontal racks, a height of roughly 12 to 18 inches off the floor keeps the base clear of damp concrete while staying easy to reach. Adjust for your ceiling height and how you load the board.

Do I need one mount or two for a snowboard?

Two supports are generally better than one because they spread the load and keep the board stable. Make sure both points are anchored to studs or solid backing.

Conclusion

A well-installed snowboard mount for wall keeps your board off the floor, protected, and ready for the next session. Choose the right style for your space, anchor it into solid framing, and check clearance for your bindings. Take a few extra minutes on the install and the setup will last for seasons.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our snowboarding guides, checking product details against manufacturer specifications and owner feedback.

About the author

Miles Sinclair
Miles Sinclair

Miles Sinclair writes reviews and buying guides for Snowboard Everest.