We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Replace BOA Dial on Snowboard Boots: Step-by-Step Guide

Learn how to replace a BOA dial on snowboard boots in a few steps. Covers identifying the dial type, removing the old one, and reinstalling it correctly.

Updated November 2026

To replace a BOA dial on snowboard boots, you remove the old dial from its mounting plate, pull out the cable tension, and fit a compatible replacement in the same orientation. Most dials are held in place by a few small screws or a snap-in mechanism, so the job takes about 20 to 30 minutes with basic hand tools. The key is matching the dial to your boot’s lacing system before you start.

Identify Your Dial Type Before You Start

BOA dials come in several generations, and they are not always interchangeable. Look at the back of the dial and the mounting plate on your boot’s shell. Note whether the dial is held by screws, a retaining clip, or a snap-fit collar. Check the BOA logo and any model markings, then confirm the replacement matches your boot brand and model year. Manufacturers usually specify compatible dial part numbers in their support documentation, so check there first.

Shopping for one? See our guide: 6 Best Replace BOA Cable Snowboard Boots Options for 2026.

Remove the Old Dial

  1. Loosen the lacing completely so the cable has no tension.
  2. Pull the cable out of the dial housing. Some systems require you to push the cable tip back through the top of the dial.
  3. Remove the screws or pry off the retaining clip holding the dial to the mounting plate. Work slowly to avoid bending the plate.
  4. Lift the dial and the cable housing out together. Note how the cable routes through the boot so you can reproduce it.

Install the Replacement Dial

Thread the new cable through the boot’s guide loops in the same path the old one followed. Seat the dial in the mounting plate, then secure it with the screws or clip. Do not overtighten screws, since the plastic housing can crack. Feed the cable end into the spool, then turn the dial clockwise by hand to take up slack until the cable sits evenly across the spool.

Check Tension and Function

Turn the dial to tighten and loosen it through its full range. The cable should wind and unwind smoothly without binding. Check that the cable runs straight from the spool to each guide loop, with no kinks. Put the boot on and tighten it to your normal snowboarding fit, then confirm the heel stays locked and the forefoot feels secure. If the cable slips or the dial clicks inconsistently, remove the cable and re-seat it on the spool.

Tools You Will Need

  • A small Phillips or Torx screwdriver, depending on your dial
  • A thin flathead or plastic trim tool for retaining clips
  • Replacement dial and matching cable, if the cable is worn
  • A clean cloth to wipe debris from the mounting area

Common Mistakes

  • Installing a dial from a different BOA generation, which may not fit the mounting plate.
  • Routing the cable differently from the original, causing uneven pressure on the foot.
  • Overtightening mounting screws and cracking the housing.
  • Skipping the function test before riding, which can leave the boot loose on the mountain.
  • Small precision screwdriver set helps you remove and reinstall small dial screws without stripping them. View on Amazon
  • Plastic trim removal tool kit lets you pry off retaining clips without scratching the boot shell. View on Amazon

FAQ

Can I replace a BOA dial myself?

Yes, most riders can do it with basic hand tools in under an hour. If the mounting plate is cracked or the boot shell is damaged, take the boots to a qualified boot fitter or repair shop. We also found Boot Dryer Red Wing: How to Dry Red Wing Boots Safely in 5 Steps useful on this point.

Do I need to replace the cable when I change the dial?

Not always. Inspect the cable for fraying, kinks, or stretching first. A worn cable can cause slipping and should be replaced at the same time.

Will a new dial fit any snowboard boot?

No. BOA dials vary by brand, model, and generation, so always match the replacement to your specific boot model and check the manufacturer’s compatibility information.

Conclusion

Replacing a BOA dial is a manageable repair when you identify the correct dial type first and route the cable exactly as the original did. Test the new dial through its full range before heading out. If the fit still feels off after the swap, a boot fitter can check your setup.

Emily Parker

About Emily Parker

Emily Parker is part of our editorial team and reviews and edits our snowboarding guides, checking product details against manufacturer specifications and owner feedback.

About the author

Emily Parker
Emily Parker

Emily Parker writes reviews and buying guides for Snowboard Everest.