We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Undo BOA Snowboard Boots Fast: A Step-by-Step Guide

Learn how to undo BOA snowboard boots in seconds, release tension correctly and avoid damaging the dial or cable. Quick steps for beginners and riders.

Updated November 2026

To undo BOA snowboard boots, you turn the dial counterclockwise to release the tension, then pull the lacing cable out of the guides or let it spool back. Done right, this takes a few seconds and keeps the cable and dial intact. The steps below cover the quick release, the full unlace, and what to do when the dial feels stuck.

Release the Tension First

Before you pull anything, back the system off. Grip the dial on the top of the boot and turn it counterclockwise. You will feel a click or a series of clicks as the ratchet disengages. Keep turning until the cable feels slack around your foot and the boot opens without force.

Shopping for one? See our guide: 6 Best Snowboard Boots with BOA for Every Rider (2026).

Avoid yanking the dial upward or prying it with a tool. The dial is designed to turn, not lift, and forcing it can strip the internal ratchet over time.

Remove the Cable from the Guides

Once the tension is gone, the cable still runs through a series of guides on the boot’s tongue and cuff. Most setups let you pull the cable out gently by hand. Follow these steps:

  1. Keep the dial turned fully counterclockwise so the cable can move freely.
  2. Slide your fingers under the cable near the top eyelets and lift it out of the first guide.
  3. Work down the boot, releasing each guide in turn, until the cable is free from the lower eyelets.
  4. Check that the cable is not twisted or caught before you pull it through.

Some models, including many Burton and Vans designs, use slightly different guide arrangements, so the path may look different from one brand to the next. The principle is the same: release tension, then guide the cable out by hand.

What to Do If the Dial Won’t Turn

A stiff dial usually has one of three causes: the cable is still under tension, the dial has collected snow or grit, or the cable has bunched up inside the housing. Start by turning the dial counterclockwise while gently pulling the laces slack from the top. If the dial still resists, wipe the dial and the area around it with a dry cloth and try again. Trapped snow melts and refreezes, so drying the boot first can help.

If the dial is cracked, the cable is frayed, or the mechanism is jammed, stop forcing it. Contact the manufacturer or a qualified boot technician rather than risking further damage.

  • Soft microfiber cloth — Useful for drying snow and grit off the dial and cable before you release tension. View on Amazon
  • Snowboard boot dryer — Helps dry out moisture inside the liner, which can stop wet cables and dials from sticking after a session. View on Amazon

Common Mistakes

  • Pulling the cable out before turning the dial fully counterclockwise, which can strain the guides.
  • Using pliers or screwdrivers on the dial, which can damage the ratchet.
  • Ignoring snow and ice buildup, which makes the dial harder to turn each time.
  • Re-threading the cable in the wrong order, which can leave uneven pressure on your foot.
  • Storing boots with the dial fully tightened, which can add stress to the cable over time.

FAQ

Can I undo BOA boots while wearing them?

Yes. Turning the dial counterclockwise releases tension while your foot is still inside, which is handy on the lift or between runs. Loosen the cable fully before trying to pull your foot out.

Do I need to remove the cable to take my boots off?

Usually not. Once the tension is released, the boot opens enough for most riders to slide their foot out. Removing the cable from the guides is only needed for cleaning, repairs or lace replacement.

Why does my BOA dial keep clicking when I loosen it?

The clicks come from the ratchet disengaging as you turn the dial. They are normal and show the system is releasing in steps. If the clicking is accompanied by resistance, check for snow or debris.

Conclusion

To undo BOA snowboard boots, turn the dial counterclockwise, then guide the cable out of the eyelets if you need to. Keep the dial clean and avoid forcing it. If the mechanism stays stuck or damaged, a professional repair is the safest next step.

Emily Parker

About Emily Parker

Emily Parker is part of our editorial team and reviews and edits our snowboarding guides, checking product details against manufacturer specifications and owner feedback.

About the author

Emily Parker
Emily Parker

Emily Parker writes reviews and buying guides for Snowboard Everest.