We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Loosen BOA Laces on Snowboard Boots: A Step-by-Step Guide

Learn how to loosen boa laces on snowboard boots in a few simple steps, plus how to release pressure points and avoid over-tightening on the slopes.

Updated November 2026

Learning how to loosen BOA laces on snowboard boots takes about thirty seconds once you know the release method. You will be able to relieve pressure on your shins, ankles or top of the foot without retying anything. The process comes down to turning the dial counterclockwise, lifting the cable slightly, and adjusting the zones that need more room.

Understand How the BOA Dial Releases

A BOA system uses a dial on the outside of the boot that spools a thin steel cable through guide loops. Turning the dial tightens the cable, and turning it the other way releases tension. Most dials click in small increments, so you can make fine adjustments rather than all-or-nothing changes. Manufacturers generally specify that you should release tension gradually instead of yanking the dial, which can strain the internal spool.

Shopping for one? See our guide: Lace vs Boa Snowboard Boots (2026): Which Is Better for Your Riding?.

Steps to Loosen BOA Laces Quickly

  1. Stand on a flat surface and unclip your bindings or sit down so your foot is stable.
  2. Locate the dial on the side or back of the boot.
  3. Turn the dial counterclockwise one click at a time until you feel the cable go slack.
  4. Pull gently on the cable guide near the pressure point to release more slack where needed.
  5. Flex your ankle and check that the boot moves freely before tightening anything again.

Loosen Specific Zones Without Losing Support

Many riders only need to ease one area, such as the top of the foot or the calf. Some boots have multiple cable zones, each with its own dial, so you can release just the zone causing discomfort. Other models use a single cable running through the full upper, which means loosening it affects the whole boot. In that case, back off a few clicks, test your stance on a flat surface, and repeat until the fit feels right. For a deeper look, How to Loosen BOA Snowboard Boots: 5 Steps for a Comfortable Fit (2026) covers this in detail.

Check Your Fit After Loosening

Once you loosen the dial, make sure your heel stays locked in the back of the boot. Stand up, rock forward and back, and bend your knees slightly. If your heel lifts more than a little, tighten one or two clicks and check again. A boot that is too loose will cause poor board control, so aim for balance between comfort and support.

Common Mistakes to Avoid

  • Turning the dial too fast, which can damage the cable or spool.
  • Loosening the entire boot when only one zone needs adjusting.
  • Ignoring a heel that slips after release, which leads to blisters and poor edge control.
  • Pulling the cable directly instead of working through the dial.
  • Forgetting to recheck fit after loosening before heading onto steeper terrain.
  • Boot liner heat moldable insoles: Owners often use these to fill gaps once they have loosened the laces and need extra heel hold. View on Amazon
  • Snowboard boot dryer: Drying liners between sessions helps the boot stay consistent so you do not overtighten to compensate for stretched padding. View on Amazon

FAQ

Can I loosen BOA laces while wearing my boots?

Yes, you can turn the dial while your boots are on, and this is often the easiest way to adjust fit on the hill. Sit down or unclip your bindings first so your balance is stable. A related read: Boot Dryer Red Wing: How to Dry Red Wing Boots Safely in 5 Steps.

What if the dial will not turn?

Check for snow, ice or debris in the dial housing, and clear it with a dry cloth. If the dial still does not move, a repair technician or the manufacturer should inspect the mechanism, since forcing it can cause damage.

How much should I loosen my BOA boots?

Release only enough to relieve pressure while keeping your heel secure. Many riders back off a few clicks at a time and test their stance before making further changes.

Conclusion

To loosen BOA laces on snowboard boots, turn the dial counterclockwise in small steps and release only the zones that need relief. Recheck your heel hold and ankle movement after each adjustment. Taking these steps slowly will keep your fit comfortable and your board control sharp all day.

Emily Parker

About Emily Parker

Emily Parker is part of our editorial team and reviews and edits our snowboarding guides, checking product details against manufacturer specifications and owner feedback.

About the author

Emily Parker
Emily Parker

Emily Parker writes reviews and buying guides for Snowboard Everest.