We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Remove BOA Dial Snowboard Boots: A Step-by-Step Guide

Learn how to remove a BOA dial from snowboard boots, including the tools you need, the steps to follow, and how to avoid damaging the lacing system.

Updated November 2026

To remove a BOA dial from snowboard boots, you unscrew or pry off the dial housing, release the tension on the lacing cable, and then pull the dial assembly out of the boot shell. The whole job usually takes a few minutes with basic hand tools. Working slowly matters more than speed, because the cable and the small plastic parts are easy to bend or lose.

Before You Start

Check whether you actually need to remove the dial. Many dial problems are fixed by replacing only the dial or the cable, and both can often be done without taking the full assembly apart. If the boot is still under warranty, contact the manufacturer first. Some brands handle dial replacement through their service department.

Shopping for one? See our guide: 6 Best Snowboard Boots with BOA for Every Rider (2026).

Step-by-Step: Removing the Dial Assembly

  1. Loosen the lacing completely by turning the dial counterclockwise until the cable is slack.
  2. Pull the cable out of the lacing guides so nothing is holding tension.
  3. Locate the retaining screw, usually on the front or side of the dial housing. Remove it with a small Phillips or Torx driver, depending on the boot.
  4. If there is no screw, gently pry the dial housing outward from the boot shell using a thin plastic pry tool. Work around the edges rather than prying from one point.
  5. Once the housing is free, pull it out slowly and guide the cable through the boot so it does not snag on stitching or liner.
  6. Keep track of every small part, including springs, clips and washers, and lay them out in order.

Handling the Cable

Do not bend the cable sharply. A kink can cause it to stick or fray later. If the cable needs to come out entirely, note how it is routed through each lacing eyelet, or take a photo before you start, so you can thread it back correctly.

Reinstalling or Replacing the Dial

When you put the assembly back, reverse the steps. Thread the cable through the same path, seat the housing firmly, and secure the retaining screw without overtightening it. Turn the dial a few times to confirm the cable winds and releases smoothly before you lace the boot. Replacement dials and cables should match your boot’s model and generation, since parts are not always interchangeable across brands.

Tools You May Need

  • Small Phillips or Torx screwdriver set
  • Thin plastic pry tool or guitar pick
  • Clean cloth and a small tray for parts
  • Phone camera for photographing the cable path

Common Mistakes

  • Forcing the housing out instead of working around the edges, which can crack the plastic.
  • Pulling the cable without releasing tension first.
  • Overtightening the retaining screw, which strips threads in the housing.
  • Losing small springs or clips during disassembly.
  • Skipping a test turn of the dial before lacing up.
  • A precision screwdriver set makes it easier to remove small retaining screws without rounding them. View on Amazon
  • A plastic pry tool kit lets you lift the housing without scratching the boot shell. View on Amazon

FAQ

Can I remove a BOA dial without taking the whole boot apart?

In most cases, yes. You usually only need to remove the retaining screw and the dial housing, and the boot liner can stay in place.

Do I need to replace the cable when I replace the dial?

Not always. Inspect the cable for fraying or kinks, and replace it if it looks worn, since a damaged cable can snap under tension.

Will removing the dial void my warranty?

It can, depending on the manufacturer. Check the warranty terms or contact the brand before you disassemble the dial.

Conclusion

Removing a BOA dial is a straightforward job if you release the tension first and work slowly around the housing. Photograph the cable path and keep the small parts organized so reassembly goes smoothly. If the dial is damaged or the boot is still under warranty, a manufacturer service center or a qualified boot technician is a safe option.

Emily Parker

About Emily Parker

Emily Parker is part of our editorial team and reviews and edits our snowboarding guides, checking product details against manufacturer specifications and owner feedback.

About the author

Emily Parker
Emily Parker

Emily Parker writes reviews and buying guides for Snowboard Everest.